石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

单层MXene纳米片Ti2N电磁特性的过渡金属(Sc、V、Zr)掺杂效应

二维材料MXene纳米片由于具有较大的比表面积和较高的电子迁移率而受到广泛的关注。本文采用基于密度泛函理论的第一性原理计算,对单层MXene纳米片Ti₂N电磁特性的过渡金属(Sc、V、Zr)掺杂效应进行了系统研究。结果表明,所有过渡金属掺杂体系结合能均为负值,结构均稳定;其中Ti₂N-Sc体系的形成能为-2.242 eV,结构更易形成,且保持稳定;掺杂后Ti₂N-Sc、Ti₂N-Zr体系磁矩增大;此外,Ti₂N-Sc体系中保留了较高的自旋极化率,达到84.9%,可预测该体系在自旋电子学中具有潜在的应用价值。     

Piezoelectric Nanogenerator Based on Electrospun Cellulose Acetate/Nanocellulose Crystal Composite Membranes for Energy Harvesting Application

Nanogenerators, as the typical conversion of mechanical energy to electrical energy devices, have great potential in the application of providing sustainable energy sources for powering miniature devices. In this work, cellulose acetate/cellulose nanocrystal(CA/CNC) composite nanofiber membranes were prepared by electrospinning method and then utilized to manufacture a flexible pressure-driven nanogenerator. The addition of CNC not only increased the content of piezoelectric cellulose I crystallization but also strengthened the mechanical deformation of the nanofiber membranes, which could greatly enhance the piezoelectric performance of CA/CNC composite membranes. The CA/CNC composite nanofiber membrane with 20%(mass fraction) of CNC(CA/CNC-20%) showed optimal piezoelectric conversion performance with the output voltage of 1.2 V under the force of 5 N(frequency of 2 Hz). Furthermore, the output voltage of the CA/CNC-20% nanogenerator device exhibited a linear relationship with applied impact force, indicating the great potential in pressure sensors.     

吉林大学化学学院研究生课程思政的多维度构建与探索*

研究生课程思政的建设影响着研究生的培养质量,关乎着能否实现立德树人这一人才培养的根本任务。介绍了吉林大学化学学院立足学科特点,在研究生课程思政建设方面取得成功的经验,并对未来的课程思政建设方向进行了探讨。     

Chelating Metal Ions in a Metal-Organic Framework for Constructing a Biomimetic Catalyst Through Post-modification

Crystal engineering, as a burgeoning technology, has been widely used to construct metalloporphyrins biomimetic catalysts. Herein, a bimetallic metal-organic framework (MOF) was constructed by 4-(4-carboxyphenyl)-1,2,4-triazole ligand, Co²⁺ and Zr⁴⁺ metal ions by solvothermal reaction(named PFC-88). A N,N-chelation site was found between the two adjacent ligands in PFC-88, consequently a porphyrin-like structure was obtained through chelating Fe³⁺ in this site by post-modification, named PFC-88-Fe. The result of a single crystal X-ray technology verified that Fe ions were successfully metalated in the N,N-chelation site of PFC-88, which is assisted by the X-ray absorption near-edge structure(XANES) spectra. An o-phenylenediamine oxidation reaction was applied to assessing the catalytic activity of PFC-88-Fe, in which the absorbance increases of phenazine-2,3-diamine at λ=418 nm were recorded by absorption spectroscopy in kinetic mode, exhibiting the application potential as a biomimetic catalyst.     

MWCNTs/hydroxypropyl cellulose/polyethylene glycol-based shape-stabilized phase change materials

Journal of Thermal Analysis and Calorimetry - Polyethylene glycol (PEG) is widely used as phase change materials (PCMs). However, the leakage and low thermal conductivity issues restrict its...     

SAPO-34提升铁钒基催化剂抗碱性能研究

采用浸渍法制备Fe-VO_x/SAPO-34和Fe-VO_x/TiO₂脱硝催化剂,探究SAPO-34分子筛与TiO₂两种载体负载铁钒基氧化物催化活性及抗碱性能的差异。借助X射线衍射(XRD)、X射线光电子能谱(XPS)、氨气程序升温脱附(NH₃-TPD)、氢气程序升温还原(H₂-TPR)、原位红外漫反射(in-situ DRIFTs)等表征手段对催化剂的骨架结构、表面物化性质、氧化还原能力以及对反应气体的吸脱附情况进行分析。结果表明:SAPO-34分子筛内部特定的孔道结构和稳定的骨架,有利于活性组分在载体上均匀分散,降低碱金属对表面活性中心的物理覆盖作用;同时其表面丰富的酸位点能够作为碱金属捕获位,保护催化剂表面的活性中心,保证催化剂的吸附-反应过程能够正常进行,从而使Fe-VO_x/SAPO-34表现出良好的抗碱金属能力。